What are your thoughts and feelings on How to Install a Bathtub Yourself?
Setting up a tub isn't specifically brain surgery, yet it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably tough task. If the old bathtub is conveniently easily accessible, the project can relocate immediately; if you need to open a wall surface to get rid of the old bathtub and place the brand-new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly assist you set up a new tub in your restroom if you have currently acquired a brand-new tub and don't need to change the setup of your previous water supply pipelines.
Your tools as well as material list ought to consist of the following:
Preparing for the Setup
First of all, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted gain access to that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, place the tub in the required placement. The wooden boards are valuable in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the supply of water as well as check all joints and also brand-new pipework for leakages as well as tighten them if needed. Load the tub and also check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait until the bathtub has actually been used at the very least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in place in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath and the tiling, leading to difficulties with dampness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealant can crack relatively very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on our other web blog. Liked our write up? Please share it. Let another person find it. Many thanks for your time spent reading it.
Immediate relief, just a call.